User manual and frequently asked questions X-PLORER Serie 75 S+
The promise of up to 60 days of peace of mind
The Rowenta X-PLORER Serie 75 Robot Vacuum Cleaner is an outstanding home cleaning solution with cutting-edge technology that leaves your entire home spotless. Discover a high-tech automatic vacuum cleaner that does the work for you—for hands-off cleaning including automatic dust emptying, high-precision navigation, advanced laser technology, and 4-in-1 cleaning with the Smart Aqua Power system for a spotless home made easy.
Do not vacuum wet surfaces, any type of liquids, hot substances (embers, cigarettes), super fine substances (plaster, cement, ash, etc.), large sharp waste (glass), harmful products (solvents, abrasives, etc.), aggressive products (acids, cleaning products, etc.), inflammable and explosive products (oil or alcohol based).
Place the charging base station against a wall, on a flat surface and where the robot vacuum cleaner can easily find it. This location must be free of any obstacles (including rugs). Leave at least 1,5 metre of space free to the left and the right, and 2 metres at the front of the base station. If the station is placed in a corner or difficult to find, the robot vacuum cleaner will not be able to reach it. Place the base station's power cable along the wall. For more information, refer to the instructions in your user manual.
Before running the robot vacuum cleaner ensure space has no obstacles, power cords, clothing, or other potentially dangerous objects which might cause the appliance breakdown or other accidents.
In the map configuration, check the suction power and wetness level settings for each room. If there are no settings, the robot automatically switches to "Dry" mode.
If you need to launch the robot with specific settings, you must select the custom mode and configure the needs at that moment. This mode uses the parameters set in the rooms customisation.
Several possible reasons exist: • If the robot did not start from its docking station, it will not return to it. In this case, the robot will return to its starting point. • If the robot vacuumed in Spot mode, the robot will return to its starting point. • If the robot is lifted up and put back down on the floor, it will try to relocate itself. If it can't, it will return to its starting point.
You can perform the following actions: • Turn off and then turn on the main power switch. • Unplug the cable and plug it again into the charging station. • Make sure that the charging terminals and the sensor windows are not clogged up, then wipe the main body and the charging station with a dry cloth. Do not forget to switch off the main power switch and to turn off the robot before drying carefully. • Check if there is no obstacle such as a reflective object, a chair, etc. near the charging station.
If after these steps, the automatic charging still does not work well, contact an approved vacuum repair company.
Check the following: • If the switch underneath the robot is correctly in the 'ON' position. • If the display is lit up. If not, charge up the robot on the base station.
The robot may experience certain problems represented by error codes. For more details about the error codes description and solution, refer to User Manual.
Check the following: • The charging station must not be installed on a rug. • The charging station must not be exposed to sunlight or near a heat source. • The free space to the side and the front of the charging station adheres to the instructions in the user manual. • The plug is correctly connected to the charging station. • The charger cable is connected to the power supply. • There are no obstructing objects around the charging base. • There are no objects near the charging station terminals. • The charging station is activated (LED indicator is green).
If after checking these elements, the robot still cannot find the base station, contact an approved vacuum repair company.
If the station's indicator light is still red after changing the dust bag with a new one: • Unplug the power cord. • Turn the station over. • Using a screwdriver, remove the 5 screws holding the cover of the dust channel and take it off. • Check whether there are any foreign objects obstructing the dust channel and remove them with your fingers or with a bottle brush. • After cleaning the dust channel, put the cover and the 5 screws back on. • Turn the station over and reconnect the power cord. • Place the robot in front of the station and press the "Home" button on the robot. • The robot will automatically go back to the station and vacuum the dust for 20 seconds. The light on the station will turn white.
Move the charging base. If it is installed in a corner or hard to find, the robot vacuum cleaner will not be able to reach it.
Place the base against a wall, where the robot vacuum cleaner can easily find it: • Make sure to keep a free space of 0.5 m at the sides and 1.5 m at the front of the base. • The area should be free of any obstacles. • The power cable should be tightly laid along the wall. • Do not install the base near stairs. • Do not place the base on a carpet or rug, but always on a flat surface.
Move the charging base. If it is installed in a corner or hard to find, the robot vacuum cleaner will not be able to reach it.
Place the base against a wall, where the robot vacuum cleaner can easily find it: • Make sure to keep a free space of 0.5 m at the sides and 1.5 m at the front of the base. • The area should be free of any obstacles. • The power cable should be tightly laid along the wall. • Do not install the base near stairs. • Do not place the base on a carpet or rug, but always on a flat surface.
Yes, it is recommended to use the robot vacuum cleaner to maintain the cleanliness, but there are still surfaces where the robot does not perform as efficient as non-robotic vacuum cleaners.
This is because the robot didn't start from its docking station: since the robot returns to its starting point, it will go back to where it began vacuuming in Spot mode.
